Power System Analysis And Design SI Edition 6th Edition By Glover - Test Bank

Power System Analysis And Design SI Edition 6th Edition By Glover – Test Bank

Instant Download – Complete Test Bank With Answers

Sample Questions Are Posted Below

Name: ________________________
ECE 476
Exam #1
Tuesday , October 11, 2011
Closed book, closed notes
One note sheet allowed
1. ________ / 25
2. ________ / 20
3. ________ / 25
4. ________ / 30
Total ________ / 100
1. (25 points total)
A 3, 300 mile, 345-kV line has series impedance of z = 0.03 + j0.4 /mile and shunt
admittance y = j5.0 x 10-6 mho/mile.
(9 pts) a. Calculate the line’s characteristic impedance Zc and the propagation
constant 
(9 pts) b. Initially assume that the receiving end of the line is open-circuited and has
a line to line voltage of 345 kV. Calculate the sending end line to line
voltage magnitude.
(7 pts) c. Draw the long line  equivalent circuit for this line, showing the values of
all parameters.
2. (20 points total)
The circuit shown below is a balanced three phase system with a wye-connected
generator producing 1 volt (phase to neutral). Assume that each inductor has an
impendance ZL = j10 and each capacitor ZC = -j15. Determine Ia, Icap, and the total
three phase complex power supplied by the y-connected voltage source.
3. (25 points total)
A 3-phase, 60Hz, 50km long, completely transposed transmission line is built using
Drake conductor. Drake conductor has an outside diameter of 1.108 inches; stranding of
26/7 (Al/St), which yields a GMR for the conductor of 0.0375 feet. Resistance at 60-Hz
for this conductor is 0.117 /mile. A horizontal tower configuration is used, with a
phase spacing of 25 feet (25 feet between left and center phases, 25 feet between center
and right, and hence 50 feet between left and right). Bundling is used, with 2 conductors
per phase, spaced 1 foot apart. For reference μ0 = 4π x 10-7 H/m and Ɛ0 = 8.854 x 10-12
F/m.
a) Find the positive sequence inductance in H/m and inductive reactance in Ω/km.
b) Find the capacitance to neutral in F/m and the admittance to neutral in S/km.
Neglect the effect of the earth plane.
c) Since the line is 50km, we can make the short line approximation. Draw the short
line π equivalent circuit, labeling appropriate values.
For reference  = 4 x 10-7 H/m and 0 = 8.854 x 10-12 F/m. There are 1609 meters
per mile.
4. Multiple Choice. Circle the most correct answer. Ten problems, three points
each for a total of 30 points.
Note this Problem Continues on the Next Page
A. As discussed in class, the most common load model for the power flow is
A. Constant impedance
B. Constant current
C. Constant power
B. We can only use per phase analysis when:
A. All loads and sources are Y connected
B. All loads and sources are delta connected
C. There is no mutual inductance between phases
D. A and C
E. B and C
C. Which statement about phase and line voltages (V) and currents (I) in Wye and Delta
connections is correct?
A. Phase I = line I in Wye, and phase V = line V in Delta
B. Phase I = line I in Delta, and phase V = line V in Wye
C. Phase I = line I and phase V = line V in Wye
D. Phase I = line I and phase V = line V in Delta
D. Using Newton’s method to solve the equation x2 –sin(x) – 2 = 0, with an initial guess of
x=1 (that is, its value at the zero iteration), select the value that is closest to the value of
x after the second iteration:
A. 1.6754
B. 1.7775
C. 1.8073
D. 2.3041
E. 2.3253
E. The impedance of a 10 MVA, 22/220 kV transformer is 0.2 per unit. What is this
impedance in per unit for a power base of 10 MVA, and a voltage base of 11 kV on the
low voltage side of the transformer?
A. 0.05 p.u.
B. 0.1 p.u.
C. 0.2 p.u.
D. 0.4 p.u.
E. 0.8 p.u.
F. Transformer open circuit (OC) and short circuit (SC) tests allow us to calculate certain
equivalent circuit values. Which parameters are calculated from the OC test and which
are from the SC test?
A. The OC test gives the resistances and the SC test gives the reactances
B. The OC test gives the series impedance and the SC test gives the shunt
admittance
C. The OC test gives the shunt admittance and the SC test gives the series
impedance
D. The OC test gives the voltages and the SC test gives currents
G. In a long line Pi model, we use series impedance Z’ and shunt admittance Y’/2. In the
short line model, we use:
A. Series impedance Z’ and shunt admittance Y’/2
B. Series impedance Z’ and shunt admittance Y/2
C. Series impedance Z and shunt admittance Y/2
D. Series impedance Z and shunt admittance 0
E. Series impedance 0 and shunt admittance 0
H. In the power flow at the slack (swing) bus,
A. P and V are fixed
B. P and Q are fixed
C. P and ƟV are fixed
D. V and Q are fixed
E. None of the above
I. A solid conductor has a conductor area of 1113 kcmils. What is its outside diameter, in
inches?
A. 1.055”
B. 1.293”
C. 1113”
D. 1.044”
J. If the diameter of a transmission line conductor is increased, then:
A. Both the inductance and the capacitance increase
B. The inductance increases and the capacitance decreases
C. The inductance decreases and the capacitance increases
D. Both the inductance and the capacitance decrease
E. The inductance decreases and the capacitance remains unchanged